|
CONTACT
US |
|
Easy Lawn Texas
2948 McPherson Road
Fort
Worth, Texas 76140
P (888)
271-8377
F (817) 478-7409
E
info@easylawntexas.com
We are an authorized dealer for
Easy Lawn products in the states of Texas, Oklahoma, New Mexico and Louisiana.
For Hydromulching
services,
contact
Phillips Lawn Sprinkler located in Fort Worth, Texas. We
specialize in all your landscaping, lawn sprinkler and Hydromulching
needs through out the states of Texas, Oklahoma, New Mexico and Louisiana. |
|
|
Hydroseeding
Equipment |
|
TURFMASTER
SERIES |
LANDSCAPER
SERIES |
CONTRACTOR
SERIES |
|
 |
 |
 |
Contractor Series
 The
Contractor Series represents Easy Lawn's entry into the
paddle agitation market. Easy Lawn had a desire to build
hydroseeding units larger than 1200 gallons, and felt that
paddle agitation was the most efficient system for these
larger tank sizes. Designed new from the ground up, Easy
Lawn was able to combine the best features from paddle
agitation units already on the market and incorporate some
innovations of our own.
The Contractor Series
units feature a 54 hp John Deere turbo diesel engine. They have an aggressive paddle design to keep
even the most difficult products in suspension. A mulch
grinder speeds loading, no
matter how much water is in
the tank. BFM's (Bonded Fiber Matrix) are mixed much better
after first passing through the grinder. You don't have the
problem of chunks of mulch floating around in the tank above
the paddles like other machines on the market. Our discharge
pump is driven hydraulically, eliminating troublesome
clutches and the need to throttle the engine to alter pump
performance. The hose reel option features a quick
disconnect so that you can couple the hose directly to the
pump. This is especially helpful when pumping extra thick
mixes. You can also disconnect the hose altogether when you
go to refill the tank with water, eliminating the need to
wind all the hose back up on the reel.
The Contractor Series has the largest top deck storage
capacity of any other hydroseeding unit on the market. Our
trailer mounted units have a ladder on the front and back
for better accessibility and a tool box in the tongue for
storage. The top deck of our units is sprayed with a
polyethylene coating that has sand embedded in it, thus
improving traction and durability. Units 1200 gallons and
larger have a sliding gate on the top deck to ease loading
of mulch and other bulk materials.
Loading the tank can be accomplished much quicker because
you can load the water, mulch, and seed, fertilizer, lime,
etc. at the same time through three separate openings. There
is an opening for filling the unit with water that has a two
inch airgap fill pipe to allow filling from a fire hydrant.
There is also a spigot on the airgap pipe to accommodate a
garden hose so that you can clean the hydroseeding unit
while you are at the water source. The second opening has a
hinged lid and a bag breaker and is used to load your seed,
fertilizer, lime, etc. The third opening is the grinder
which is used for the loading of hydroseeding mulch into the
tank.
The Contractor Series units are very easy to operate. All
engine, paddle, and grinder controls are centrally located
on the side of the grinder. Each set of controls is color
coded and bilingual. That's right, our control panel's major
functions are in English and Spanish. They feature a two
stage electronic throttle, one position for mixing and one
position for spraying. There is a reversible paddle
direction valve and a separate speed control valve. The
grinder has a reversible valve right next to the paddle
direction valve. To the right of the paddle/grinder controls
is the engine control panel. It features the key switch,
preheat coil, and indicator lights for oil pressure,
temperature, and charge. Just below the engine panel is a
tachometer with hour meter and a hydraulic pressure gauge.
On the bottom of the control panel, we have included concise
mixing instructions and mulch capacities for the machine.
Pump output is adjusted with the Pump Speed Control (PSC), a
simple hydraulic valve mounted right next to the turret gun.
Along side the PSC are provisions for the four turret
nozzles that come standard with the machine.
Easy Lawn strived to keep maintenance to a minimum on the
Contractor Series, and the end result is a paddle agitation
hydroseeding unit with maintenance requirements comparable
to our jet agitation machines. Stainless steel tanks are
standard, thus eliminating concerns over tank corrosion from
the lime, fertilizer, and water commonly mixed in these
machines. There are no clutches, belts, or chains to
maintain, tension, or replace. There are no tank seals that
require daily greasing. The only grease points are the
turret swivel and the hose reel swivel, and these only need
to be greased weekly. The combination of no gussets on the
inside of the tank and the use of stainless steel with a
smooth 2B finish make our tanks very easy to clean out at
the end of the day.
All of these features would be pointless if the Contractor
Series doesn't perform, and perform they do. Our discharge
pump has more flow and pressure than any other paddle
machine on the market. The Contractor Series will easily
pump through 300' of 1 1/4" hose or will spray up to 170'
with the turret gun. These units are available in 950, 1250,
and 1700 gallons and will hold more mulch than any other
machine on the market of comparable size.
The C95 and C125 are available skid or trailer mounted, and
the C170 is available chassis mounted only. Coming soon will
be 2800 and 3300 gallon versions of the Contractor Series
featuring a 174 hp John Deere turbo diesel, dual paddles, and dual
discharge pump capability.
C95
|
 |
|
Engine: |
Pump: |
|
50 HP John Deere Engine |
4"x3" Centrifugal
HPV7H Pump - 110psi620gpm max
10 0psi Operating Pressure |
|
Tank Working Capacity and Mulch Capacity: |
Hose Spray Distance w/ Straight Nozzle |
|
900 Gallons - 350 -450lbs.
Fuel Capacity: 28 gallons |
100' of hose - up to 95'
200' of hose - up to 80'
300' of hose - up to 55' |
|
C125
|
 |
|
Engine: |
Pump: |
|
50 HP John Deere Engine |
4"x3" Centrifugal
HPV7H Pump - 110psi620gpm max
100psi Operating Pressure |
|
Tank Working Capacity and Mulch Capacity: |
Hose Spray Distance w/ Straight Nozzle |
|
1200 Gallons - 450-600lbs.
Fuel Capacity: 28 gallons |
100' of hose - up to 95'
200' of hose - up to 80'
300' of hose - up to 55' |
|
C170
|
 |
|
Engine: |
Pump: |
|
50
HP John Deere Engine |
4"x3" Centrifugal
HPV7H Pump - 110psi 620gpm max
100psi Operating Pressure |
|
Tank Working Capacity and
Mulch Capacity: |
Hose Spray Distance w/
Straight Nozzle |
|
1550 Gallons - 550 -750lbs.
Fuel Capacity: 28 gallons |
100' of hose - up to 95'
200' of hose - up to 80'
300' of hose - up to 55' |
|
C280/330
|
 |
|
Engine: |
Pump: |
|
C330 170 hp Turbo Diesel John Deere
Engine |
5"x
3" Centrifugal
C330 HPV10 Pump -150psi/400gpm max
|
|
Tank Working Capacity and
Mulch Capacity: |
Hose Spray Distance w/
Straight Nozzle |
|
C330 3000 Gallons 1200-1500lbs.
C330 w/ Flush Tank - 3000 Gallons -
1200 -1500 lbs.
Turret Spray Distance w/ Straight Nozzle
C330 - up to 275' |
100' of hose - up to 95'
200' of hose - up to 80'
300' of hose - up to 55' |
|
Empty Time |
Unit Weights |
|
C330
Hose: 72 min.
Turret: 10 min
Both:
9 min. |
C330 Chasis
Empty: 9,180 lbs
Full: 39,700 lbs |
|
|
